Motor Vehicle Maintenance and Repair Stack Exchange
Motor Vehicle Maintenance and Repair Stack Exchange

Most Popular

more tags
1500 questions
9
votes
2 answers

Repairing crack on edge of windshield

I was replacing my windshield wiper motor (after asking about it here) and while putting in the new windshield wiper motor, I hit it on the edge of the windshield causing a few cracks. I asked a couple people about fixing it. The one person told me…
SameOldNick
  • 247
  • 2
  • 3
  • 8
9
votes
3 answers

Why does a starter "bounce"?

Custom 4-cylinder boxer, based on a Volkswagen/Porshe of some kind (not entirely sure what), with the starter from an '85 Nissan Sentra or thereabouts. (generic part number 16816) Video of two attempts with fuel and spark disabled, and oscilloscope…
AaronD
  • 612
  • 1
  • 5
  • 13
9
votes
2 answers

Best way to approach a tire with a bubble in the sidewall

I found a bubble in my front right tire's sidewall on my 2006 Mazda3 2.3L (FWD, open diff). So it needs to be replaced. The replacement tire will end up going on the rear as it's time to rotate them anyway. Will any damage be done by putting the…
Parker
  • 774
  • 1
  • 6
  • 11
9
votes
3 answers

What is so special about catalytic converters that makes them a target for theft?

Recently, in New Jersey, people have been stealing catalytic converters from cars. Why are people stealing this specific part all of a sudden? It happened to 4 people on my parents' street. I am wondering why this is the new thing and why they are…
Ilianna
  • 227
  • 2
  • 6
9
votes
3 answers

What is this solid electric component with three poles in a classic 50's car?

I'm restoring a 1955 Studebaker President and it has an electric component I also seen in other 50's cars, but don't know what is it for. It is similar to this stuff, right now it is disconnected... So what's its purpose? How is it called?
Aram Alvarez
  • 391
  • 1
  • 10
9
votes
5 answers

Caliper piston will not collapse on Almera 98

I was changing brake pads on a Nissan Almera 98 and I accidentally pumped the brake piston a bit out. I tried putting it back with a C clamp and the old pad but it won't budge. It's completely stuck! What should I do?
JohnD
  • 91
  • 1
  • 2
9
votes
2 answers

I stored my click torque wrench in a mid-high setting. Is it ruined?

It's an EPAuto 1/4" drive 20-200 in-lbs. I stored it at mid to high setting, and it stayed that way for months, unfortunately. Is it now significantly off from calibration?
feelthhis
  • 211
  • 3
  • 5
9
votes
4 answers

Motorcycle moves forward when in gear even with clutch lever pulled

I recently bought a KTM Adventure 390. When I start the bike in neutral and then shift to first gear, the bike moves(jerks) forward a little, even though the clutch lever is still pulled all the way. Is this normal?
positron
  • 93
  • 1
  • 1
  • 5
9
votes
6 answers

How much protection do grill guards give?

My wife was just rear-ended by some woman who was "tired" (her claim—in fact she was more probably texting) and not paying attention. This did a lot of damage to the rear end of our Honda Pilot. This is the third accident my wife has been in in a…
iconoclast
  • 201
  • 1
  • 2
  • 6
9
votes
3 answers

My motorcycle is refusing to start, which common problems should I look for?

I've just taken my motorcycle out of storage, I rode her around the block once, parked her, and now she is refusing to turn over. The starter seems to be running fine. I've just filled the tank with new fuel, and replaced the oil. Also, the battery…
blueberryfields
  • 349
  • 3
  • 10
9
votes
1 answer

Can I use an OBD2 Scan Tool on older GM vehicle?

I can get an adapter that connects my OBD2 scan tool to my 12 pin GM scan tool connection. But will the tool be able to read the codes and tell me anything useful? Or do I need to get a scan tool that is also aware of OBD-1 or GM specific codes? I…
Jim
  • 248
  • 1
  • 2
  • 8
9
votes
1 answer

Battery drops to 10.5 volts after charging

A few days ago, my 97 Corolla had trouble starting. It cranks but doesn't start, maybe due to a problem with the carburetor. Figured I might discharge the battery, so I stopped my attempts at starting. Fast forward to this morning, I tried to start…
demiglace
  • 213
  • 1
  • 2
  • 5
9
votes
2 answers

Honda Accord radio anti-theft code not working...what am I doing wrong and what should I do?

I had to remove the battery so I can replace the driver's side low beam headlight. I didn't bother to buy a settings saver because I found the security code in my Honda's packet (I bought this car used and luckily the owner was pretty organized with…
milesmeow
  • 1,089
  • 8
  • 16
  • 24
9
votes
10 answers

Trying to solder broken mount, solder won't stick?

I have a horn with spade connectors. They are stamped to the horn body and one is broken. I figured I could just use a stud ring terminal and solder it to the stud. I cleaned the stud with a copper wire brush, but the solder just wouldn't stick to…
wild.coast
  • 348
  • 3
  • 13
9
votes
1 answer

What is name of this part in the picture?

Could you guys please tell me the name of the part in red square in English?
Sodbileg Gansukh
  • 193
  • 1
  • 5
1 2 3
…
99 100